HEAT EXCHANGER CLEANING SYSTEM TEXAS CITY TEXAS

Heat Exchanger Cleaning System Texas City Texas

Heat Exchanger Cleaning System Texas City Texas

A heat exchanger is a device used to transfer heat between a solid object and a fluid, or between two or more fluids. The fluids may be separated by a solid wall to prevent mixing or they may be in direct contact. They are widely used in space heating, refrigeration, air conditioning, power stations, chemical plants, petrochemical plants, petroleum refineries, natural-gas processing, and sewage treatment. The classic example of a heat exchanger is found in an internal combustion engine in which a circulating fluid known as engine coolant flows through radiator coils and airflows past the coils, which cools the coolant and heats the incoming air. Another example is the heat sink, which is a passive heat exchanger that transfers the heat generated by an electronic or a mechanical device to a fluid medium, often air or a liquid coolant. Heat Exchanger Cleaning System Texas City Texas

There are three primary classifications of heat exchangers according to their flow arrangement. In parallel-flow heat exchangers, the two fluids enter the exchanger at the same end, and travel in parallel to one another to the other side. In counter-flow heat exchangers the fluids enter the exchanger from opposite ends. The counter current design is the most efficient, in that it can transfer the most heat from the heat (transfer) medium per unit mass due to the fact that the average temperature difference along any unit length is higher. See countercurrent exchange. In a cross-flow heat exchanger, the fluids travel roughly perpendicular to one another through the exchanger. Heat exchangers cleaning system Texas City Texas

For efficiency, heat exchangers are designed to maximize the surface area of the wall between the two fluids, while minimizing resistance to fluid flow through the exchanger. The exchanger’s performance can also be affected by the addition of fins or corrugations in one or both directions, which increase surface area and may channel fluid flow or induce turbulence. Heat Exchanger Cleaning System Texas City Texas

The driving temperature across the heat transfer surface varies with position, but an appropriate mean temperature can be defined. In most simple systems this is the “log mean temperature difference” (LMTD). Sometimes direct knowledge of the LMTD is not available and the NTU method is used. Heat Exchanger Cleaning System Texas City Texas

Types Heat exchangers cleaning system Texas City Texas Double pipe heat exchangers are the

Heat Exchanger Cleaning System Texas City Texas

simplest exchangers used in industries. On one hand, these heat exchangers are cheap for both design and maintenance, making them a good choice for small industries. On the other hand, their low efficiency coupled with the high space occupied in large scales, has led modern industries to use more efficient heat exchangers like shell and tube or plate. However, since double pipe heat exchangers are simple, they are used to teach heat exchanger design basics to students as the fundamental rules for all heat exchangers are the same. Heat Exchanger Cleaning System Texas City Texas

Shell and tube heat exchanger Heat exchangers cleaning system Texas City Texas

A shell and tube heat exchanger Heat Exchanger Cleaning System Texas City Texas

Heat exchangers cleaning system Texas City Texas Shell and tube heat exchangers consist of series of tubes. One set of these tubes contains the fluid that must be either heated or cooled. The second fluid runs over the tubes that are being heated or cooled so that it can either provide the heat or absorb the heat required. A set of tubes is called the tube bundle and can be made up of several types of tubes: plain, longitudinally finned, etc. Shell and tube heat exchangers are typically used for high-pressure applications (with pressures greater than 30 bar and temperatures greater than 260 °C). This is because the shell and tube heat exchangers are robust due to their shape. Heat exchangers cleaning system Texas City Texas
Several thermal design features must be considered when designing the tubes in the shell and tube heat exchangers: There can be many variations on the shell and tube design. Typically, the ends of each tube are connected to plenums (sometimes called water boxes) through holes in tube sheets. The tubes may be straight or bent in the shape of a U, called U-tubes.Heat Exchanger Cleaning System Texas City Texas

• Tube diameter: Using a small tube diameter makes the heat exchanger both economical and compact. However, it is more likely for the heat exchanger to foul up faster and the small size makes mechanical cleaning of the fouling difficult. To prevail over the fouling and cleaning problems, larger tube diameters can be used. Thus to determine the tube diameter, the available space, cost and fouling nature of the fluids must be considered. Heat Exchanger Cleaning System Texas City Texas
• Tube thickness: The thickness of the wall of the tubes is usually determined to ensure:
  • There is enough room for corrosion
  • That flow-induced vibration has resistance
  • Axial strength
  • Availability of spare parts
  • Hoop strength (to withstand internal tube pressure)
  • Buckling strength (to withstand overpressure in the shell) Heat exchangers cleaning system Texas City Texas
• Tube length: heat exchangers are usually cheaper when they have a smaller shell diameter
  

  Heat Exchanger Cleaning System Texas City Texas

  and a long tube length. Thus, typically there is an aim to make the heat exchanger as long as physically possible whilst not exceeding production capabilities. However, there are many limitations for this, including space available at the installation site and the need to ensure tubes are available in lengths that are twice the required length (so they can be withdrawn and replaced). Also, long, thin tubes are difficult to take out and replace. Heat exchangers cleaning system Texas City Texas

• Tube pitch: when designing the tubes, it is practical to ensure that the tube pitch (i.e., the center-center distance of adjoining tubes) is not less than 1.25 times the tubes’ outside diameter. A larger tube pitch leads to a larger overall shell diameter, which leads to a more expensive heat exchanger. Heat Exchanger Cleaning System Texas City Texas
• Tube corrugation: this type of tubes, mainly used for the inner tubes, increases the turbulence of the fluids and the effect is very important in the heat transfer giving a better performance. Heat exchangers cleaning system Texas City Texas
• Tube Layout: refers to how tubes are positioned within the shell. There are four main types of tube layout, which are, triangular (30°), rotated triangular (60°), square (90°) and rotated square (45°). The triangular patterns are employed to give greater heat transfer as they force the fluid to flow in a more turbulent fashion around the piping. Square patterns are employed where high fouling is experienced and cleaning is more regular. Heat Exchanger Cleaning System Texas City Texas
• Baffle Design: baffles are used in shell and tube heat exchangers to direct fluid across the tube bundle. They run perpendicularly to the shell and hold the bundle, preventing the tubes from sagging over a long length. They can also prevent the tubes from vibrating. The most common type of baffle is the segmental baffle. The semicircular segmental baffles are oriented at 180 degrees to the adjacent baffles forcing the fluid to flow upward and downwards between the tube bundle. Baffle spacing is of large thermodynamic concern when designing shell and tube heat exchangers. Baffles must be spaced with consideration for the conversion of pressure drop and heat transfer. For thermo economic optimization it is suggested that the baffles be spaced no closer than 20% of the shell’s inner diameter. Having baffles spaced too closely causes a greater pressure drop because of flow redirection. Consequently, having the baffles spaced too far apart means that there may be cooler spots in the corners between baffles. It is also important to ensure the baffles are spaced close enough that the tubes do not sag. The other main type of baffle is the disc and doughnut baffle, which consists of two concentric baffles. An outer, wider baffle looks like a doughnut, whilst the inner baffle is shaped like a disk. This type of baffle forces the fluid to pass around each side of the disk then through the doughnut baffle generating a different type of fluid flow. Heat exchangers cleaning system Texas City Texas

• 

  Heat Exchanger Cleaning System Texas City Texas

  A pillow plate exchanger is commonly used in the dairy industry for cooling milk in large direct-expansion stainless steel bulk tanks. The pillow plate allows for cooling across nearly the entire surface area of the tank, without gaps that would occur between pipes welded to the exterior of the tank. Heat exchangers cleaning system Texas City Texas

• The pillow plate is constructed using a thin sheet of metal spot-welded to the surface of another thicker sheet of metal. The thin plate is welded in a regular pattern of dots or with a serpentine pattern of weld lines. After welding the enclosed space is pressurized with sufficient force to cause the thin metal to bulge out around the welds, providing a space for heat exchanger liquids to flow, and creating a characteristic appearance of a swelled pillow formed out of metal. Heat Exchanger Cleaning System Texas City Texas

●        Fluid heat exchangers Heat exchangers cleaning system Texas City Texas

• This is a heat exchanger with a gas passing upwards through a shower of fluid (often water), and the fluid is then taken elsewhere before being cooled. This is commonly used for cooling gases whilst also removing certain impurities, thus solving two problems at once. It is widely used in espresso machines as an energy-saving method of cooling super-heated water to use in the extraction of espresso. Heat exchangers cleaning system Texas City Texas
• A waste heat recovery unit (WHRU) is a heat exchanger that recovers heat from a hot gas stream while transferring it to a working medium, typically water or oils. The hot gas stream can be the exhaust gas from a gas turbine or a diesel engine or a waste gas from industry or refinery. Heat exchangers cleaning system Texas City Texas
• Large systems with high volume and temperature gas streams, typical in the industry, can benefit from steam Rankine cycle(SRC) in a waste heat recovery unit, but these cycles are too expensive for small systems. The recovery of heat from low-temperature systems requires different working fluids than steam. Heat exchangers cleaning system Texas City Texas
• An organic Rankine cycle (ORC) waste heat recovery unit can be more efficient at low-temperature range using refrigerants that boil at lower temperatures than water. Typical organic refrigerants are ammonia, pentafluoropropane (R-245fa and R-245ca), and toluene. Heat exchangers cleaning system Texas City Texas
• The refrigerant is boiled by the heat source in the evaporator to produce super-heated vapor. This fluid is expanded in the turbine to convert thermal energy into kinetic energy, that is converted to electricity in the electrical generator. This energy transfer process decreases the temperature of the refrigerant that, in turn, condenses. The cycle is closed and completed using a pump to send the fluid back to the evaporator. Heat exchangers cleaning system Texas City Texas
• Phase-change heat exchangers Heat Exchanger Cleaning System Texas City Texas
• Typical kettle reboiler used for industrial distillation towers Heat exchangers cleaning
  

  Heat Exchanger Cleaning System Texas City Texas

  system Texas City Texas

• Heat exchangers cleaning system Texas City Texas
• Typical water-cooled surface condenser
• In addition to heating up or cooling down fluids in just a single phase, heat exchangers can be used either to heat a liquid to evaporate (or boil) it or used as condensers to cool a vapor and condense it to a liquid. In chemical plants and refineries, reboilers used to heat incoming feed for distillation towers are often heat exchangers.
• Distillation set-ups typically use condensers to condense distillate vapors back into liquid.
• Power plants that use steam-driven turbines commonly use heat exchangers to boil water into steam. Heat exchangers or similar units for producing steam from water are often called boilers or steam generators.
• In the nuclear power plants called pressurized water reactors, special large heat exchangers pass heat from the primary (reactor plant) system to the secondary (steam plant) system, producing steam from water in the process. These are called steam generators. All fossil-fueled and nuclear power plants using steam-driven turbines have surface condensers to convert the exhaust steam from the turbines into condensate (water) for re-use.
• To conserve energy and cooling capacity in chemical and other plants, regenerative heat exchangers can transfer heat from a stream that must be cooled to another stream that must be heated, such as distillate cooling and reboiler feed pre-heating.
• This term can also refer to heat exchangers that contain a material within their structure that has a change of phase. This is usually a solid to liquid phase due to the small volume difference between these states. This change of phase effectively acts as a buffer because it occurs at a constant temperature but still allows for the heat exchanger to accept additional heat. One example where this has been investigated is for use in high power aircraft electronics. Heat Exchanger Cleaning System Texas City Texas
• Heat exchangers functioning in multiphase flow regimes may be subject to the Ledinegg instability. Heat Exchanger Cleaning System Texas City Texas

Call Now:+1-856-678-4004

[email protected]

(Texas City, Texas) (Baton Rouge, Louisiana)

Nueva Orleans• Baton Rouge• Shreveport• Lafayette• Lake Charles• Kenner• Bossier City• Monroe• Alexandria• Houma• Nueva Iberia• Slidell• Ruston• Sulphur• Hammond• Natchitoches• Gretna• Chalmette• Opelousas•  Zachary• Thibodaux• Pineville• Baker• Crowley• Minden• West Monroe• Morgan City• Abbeville• Bogalusa• Mandeville• Bastrop• DeRidder• Eunice• Jennings• Denham Springs• Gonzales• Harahan • Houston• San Antonio• Dallas• Austin• Fort Worth• El Paso• Arlington• Corpus Christi• Plano• Laredo• Lubbock• Garland• Irving• Amarillo• Grand Prairie• Brownsville• Pasadena• Mesquite• McKinney• McAllen• Killeen• Waco• Carrollton• Beaumont• Abilene• Frisco• Denton• Midland• Wichita Falls• Odessa• Round Rock• Richardson• Tyler• Lewisville• College Station• San Angelo• Pearland• Texas City Texas